New colours! Glitzy and colourful. New resin bangles in the Jewellery Shop.

New colours! Glitzy and colourful. New resin bangles in the Jewellery Shop.
Add a touch of colour to your outfits with these fun and colourful resin bangles. Magnetic clasps make these ideal for girls who find it hard to get a traditional bangle on their wrist. And they're available in a range of sizes to suit small, medium and large wrists. Check them out in the Resin Jewellery Shop!

Friday, April 29, 2016

From Perfume Bottle to Home Decor using Amazing Casting Products

Over the past month I've shared a few of my resin jewellery-making ideas with you as the Featured Artist on the Amazing Casting Products blog. But resin doesn't have to be reserved only for jewellery - it is equally suitable for creating home decorator items. The starting point for my final project, the "Inspiration Post", is a beautiful Egyptian Perfume bottle that I'll be recreating in resin.

You can read about the backstory that inspired these beautiful bottles on the Amazing Casting Products blog. Whilst you're there, take a look through the archives for some other wonderful inspiration.

I was a bit nervous undertaking this project because I had no idea if I’d be able to remove my precious bottle from the Mold Putty once it had cured. But I took a deep breath and proceeded anyway!

Here’s what you’ll need to create the mould for the central bead:
To cast the bead, you’ll need:
To assemble the bottle, you’ll need these items:
First things first, you have to work out how much Mold Putty you need to make the mould! Well, I know this is stating the obvious, but you need twice as much as you’d use to create a half bottle. By that I mean, measure out enough of one part to go around half the bottle and then measure out that same amount of the other part. Simple!
This bottle stands at 10cm (4”), so it’s quite a large amount to mix and you have to work fast to blend it. Flatten it out into a rough circle and then wrap it around the bulbous part of the bottle, making sure it's pressed right against the glass so you get a good impression. You can see the seam where the two sides meet. Make sure that they are well joined so the mould will be leak proof along the seam. And then set it on its side to cure.

Happily, I was able to slice the seam open with a Stanley Knife and take my precious bottle out. I can tell you I was quite relieved! 
You will probably need to trim the bottom of the mould with the knife to level it. 
Because the mould is open-ended it needs to be plugged at the trimmed end with plasticine. The plasticine also acts as an adhesive to make sure that the mould stays firmly upright whilst you're pouring the resin. 
The final step in preparing the mould is wrapping it tightly with rubber bands to make sure it’s water tight (or rather, resin-tight!). Mix and colour the resin according to the package instructions and pour it into the mould. For this first piece, I coloured the resin with Alumilite red dye.
It’s always exciting to see your first cast out of a mould and this one is no exception. As expected, the Clear Casting Resin has picked up all the detail from the mould. One thing I learned from the first piece I cast is that this mould needs to be filled very slowly to avoid air pockets getting trapped in the lattice detail. My second and third pours were much more successful because I dripped the resin into the mould and allowed it to slowly rise up inside.
So now you have these fabulous bulb-shaped beads. But to turn them into bottle components, they need holes. I used a Dremel with a 1.5mm drill bit on very slow speed – first from one end, and then the other, with the aim of meeting in the middle. 
Before assembling the Faux Egyptian Perfume bottles, prepare some flower filigrees by drilling a stringing hole, cutting the petals apart and shaping them. I used Tim Holtz Tonic Studio scissors because the micro-serrated edge will easily cut through thin metal stampings.
Now it’s time to raid your findings stash to find components that will help you recreate a life size Faux Egyptian perfume bottle. The idea here is to combine bead caps in different sizes and shapes with a smattering of beads and crystals to represent the decorative elements of the stem and the perfume dropper.
Once you're happy with the balance of the components (and it looks like a perfume bottle) make sure that each component is nesting snugly inside the one above and below it and that there’s no play in the finished piece. If they don't fit snugly, or they slide around inside each other, the finished bottle will sit crookedly. Create a simple jewellery-making loop as close to the top bead as you can to securely finish them off.
Tip: Using rigid florist wire rather than regular jewellery-making wire gives the bottle a strong core so the bottle will stand upright on its own.
To create the gold version, I dusted the inside of the mould thoroughly with Gold Metallic Powder and coloured the resin with black dye.
The Pineapple bottle was cast with black resin and the lattice was highlighted with a Krylon Gold Leafing pen. The leaves are created by stacking petal bead caps inside each other.
My resin bottles make a wonderful grouping together and would look lovely on a dressing table.... perhaps a beautiful gift for your mother on Mother's Day. You may not have an Egyptian Perfume bottle of your own but take a look at what collectables you do have and see what might be worthy of reproducing in resin. 

For more inspiration, please join me on Facebook or visit my website for resin workshop information. 

'Til next time......

Saturday, April 16, 2016

Steampunk Resin Jewellery with a Bright and Modern Twist

Did you know that I'm the featured artist over at the Amazing Casting Products blog this month?

Each Friday/Saturday, one of my resin projects will be featured or there will be a little article where you can learn some fun facts about me as I have fun playing with resin.

Today I share a tutorial on how to make this bright and bold "Steampunk-esque" necklace.

I had so much fun with these resin cogs and wheels that I couldn't stop at just one piece. Here's a piece I glammed up with Swarovski crystals.

And another variation. Steampunk never looked so bright and fresh!

These pieces are not for the faint-hearted - they are big and bold and really make a statement!

So if you've got an afternoon free, why not give this project a go - you can re-create this catwalk-worthy piece in just a few hours.

'Til next time.........

Wednesday, April 13, 2016

Marbled and Textured Resin Bracelet

If you follow me on Instagram, then you've most likely seen this photo come through your feed:

So today, I'm going to share how I made that really cool bracelet.

You'll need to gather a few things:

Alumilite Amazing Casting Resin
Alumilite Red dye
Alumilite Violet Dye
Alumilite silver metallic powder
Silicone texture mould - I used Kraft Lady AMKT 4 Rococo (see for stockists)
Soft bristled brush
Open back silver oval bracelet blank
Teflon Craft Sheet
Permanent marker
Scrap of  paper
Tim Holtz Tonic Studios Scissors
Stanley knife
5-minute Araldite or strong adhesive like E6000
Measuring cups and wooden stir sticks

Brush the surface of the texture mould with the silver powder. Leave some areas lighter and some areas uncovered.

Measure 7.5mls (1/4oz) of each part.

Colour Part A with two drops of violet dye.

Add Part B to the cup and mix according to the package instructions. Pour in a puddle on the texture mould and then spread it out to approximately 3mm (1/8") thick.

Once cured, peel the textured resin away from the silicone texture mat.

For the marbled pieces of the bracelet, measure equal parts of Parts A and B. Add 1 drop of red dye to Part A.

Mix the two parts together. Working quickly, add 1 or 2 drops of each of the red and violet dyes and swirl them lightly through the resin.

Pour the resin into a puddle on the craft sheet and spread it to 3mm (1/8") thick. Set aside to cure.

Place the bracelet blank on your work surface with the back facing upwards. Position the scrap paper over one of the ovals and press it down so that it leaves an impression. Pierce the centre of the oval with the scissors and cut it out to create a template.

Place the template over the two pieces of resin and trace out three marbled ovals and two textured ovals.
  Cut them out.........

and shave away any rough edges with the Stanley knife so they fit firmly inside the bezels of the bracelet.

Adhere the pieces inside the bezels with your choice of adhesive.

I absolutely adore all the different shades of purple that were created when the red and violet mixed together as I swirled the colours through the resin. But maybe you're not a purple girl.... maybe you prefer blue or green or yellow. So play around with the colour combinations you like to make a bracelet that works with your wardrobe. And then wear your bracelet and listen to everyone rave over how gorgeous it is!

'Til next time.......


Blog Widget by LinkWithin